HPO Home Owner Builder Practice Test

These questions are part of the practice quiz. Start practicing

• What is the minimum ground clearance for siding?
• What basic safety practices should a Home Owner Builder follow on-site?
• 38 millimeters is equal to which of the following inches?
• What configuration is required for fire and carbon monoxide alarms?
• What is the minimum stair width?
• What is the minimum slope for asphalt shingles?
• How should a Home Owner Builder handle contingencies in the project budget?
• Which statement best describes the vent requirement?
• What must be kept from freezing for the entire build?
• What is the minimum concrete slab thickness?
• How should waste and debris be managed on a Home Owner Builder site?
• What happens if a building permit expires before project completion?
• Which insulation value set is correct according to the standards given?
• Are accessibility standards universally required for all Home Owner Builder projects?
• How should a Home Owner Builder handle weather-related delays?
• With foam, what must be done regarding joints to prevent leaks?
• Which document is typically required as part of project submittals to verify design intent?
• What happens if a submittal is rejected by the building department?
• What is the maximum distance from the roof for the final nail in drywall?
• What is the minimum board size for floor cross bracing?
• Which records should a Home Owner Builder maintain during construction?
• How does energy efficiency affect Home Owner Builder projects?
• What is the minimum joist end bearing on framing?
• For a 32 MPa concrete, what is the specified water-to-cement ratio and air entrainment?
• What is the primary purpose of a Home Owner Builder permit?
• What is the maximum spacing for studs and joints?
• What is a mechanic's lien and why should a Home Owner Builder be aware of it?
• What is the minimum nosing size?
• What is the minimum end bearing expressed in inches for joists and rafters?
• What is the maximum aggregate size relative to flatwork?
• Which statement describes what a Certificate of Occupancy authorizes?
• Why is zoning compliance important for a Home Owner Builder project?
• Fenestration refers to which aspect of a building?
• What is the minimum insurance amount for a dwelling unit in fee simple ownership?
• What are the minimum dimensions of a crawl space opening in millimeters?
• When substitutions are considered for approved materials, who must approve them in writing?
• If the original purchase price was 180,000, what is the minimum insurance?
• How many inspections are commonly required for a typical Home Owner Builder project from foundation to occupancy?
• Which option correctly states the minimum anchor bolt size and spacing?
• What is a typical consequence of not managing waste per local regulations?
• What must pipes be able to do with heating or air conditioning?
• What is the minimum clearance required between the ground and siding?
• What is the minimum drip offset for flashing?
• Which documents are typically required for a Home Owner Builder permit application?
• What is the minimum depth for anchor bolts set in concrete?
• Which warranty covers structural defects?
• What is the purpose of downspouts on a building?
• Why is an inspection of the foundation critical on a Home Owner Builder project?
• Vents are required to have what minimum percentage at the top and bottom of the space?
• What is the minimum horizontal clearance between an air intake and a gas relief device?
• What is a typical submittal a Home Owner Builder would provide for approval?
• After occupancy, what ongoing responsibilities does a Home Owner Builder have?
• Windows and doors must have which features?
• What considerations apply when demolishing a structure as a Home Owner Builder?
• If the original purchase price was 250,000, what is the minimum insurance?
• What is the minimum air changes per hour based on ventilation type?
• The minimum door height equals which inches value?
• What is the maximum aggregate size relative to the vertical form?
• Who is the primary recipient of notices to owner or notices of lien rights?
• What considerations apply to roofing in a Home Owner Builder project?
• What is the minimum exterior strip footing width?
• What is the minimum size for a stair tread including nosing?
• Why should a Home Owner Builder consider environmental impact beyond erosion control?
• What is the minimum overlap of siding?
• What does occupancy clearance indicate?
• What is the minimum tread thickness?
• In bathrooms and kitchens, what must be installed for permeable materials?
• What is the maximum furring spacing?
• If the goal is to limit solar heat gain through windows, which property should be prioritized?
• What is the purpose of erosion and sediment control on a construction site?
• What is the minimum end bearing for bearing joists and rafters?
• For permeable materials in bathrooms/kitchens, the maximum membrane thickness is not to exceed what value?
• The minimum stair width in millimeters corresponds to which approximate feet measurement?
• What documentation should be kept for materials used in a Home Owner Builder project?
• What is the minimum snow load on the roof in kilopascals?
• What disclosure obligations may apply to a Home Owner Builder?
• Fenestration affects which building performance aspect most directly?
• After the final inspection is approved, what document is typically issued?
• Under most Home Owner Builder rules, which trades usually require licensed professionals?
• If the frost line is 1.0 m, what is the minimum footing depth?
• In the two-plane cladding concept, what is the function of the second plane?
• In a two-plane cladding system, what is the purpose of the two planes?
• To compare energy performance of different windows, which metric would you examine first?
• Which property is most directly related to heat entering from the sun through glazing?
• For the 5-year warranty, which area is addressed?
• The building envelope is addressed under which warranty period?
• What does U-value measure in window assemblies?
• What is the minimum load rating for soil under a footing?
• Which type of insurance covers the project from frame through completion?
• How should a Home Owner Builder handle substitutions to approved materials?
• How deep must footings be in undisturbed soil?
• Do Home Owner Builders typically provide warranties on their work?
• What is the minimum number of layers required for asphalt shingles?
• Which statement is true about a high U-value?
• Which document is used to protect against future lien claims during construction?
• 19 millimeters is equal to how many inches?
• What is indemnification in a construction contract?
• What is the minimum strip footing width for a 2-story building?
• What is the minimum clearance between concrete or masonry chimney and combustible framing?
• The 10-year warranty covers which of the following?
• Which items are covered under the 2-year warranty?
• What is the minimum back distance for flashing?
• Which of the following pairs is correctly matched?
• Which set of features is typically required for fire safety in new residential construction?
• Which of the following is NOT an accepted expression of the minimum slope for asphalt shingles?
• What is the minimum vertical clearance above the air intake required for exhaust vents?
• At what width does a header need to be doubled?
• Which metric measures the overall rate of heat transfer through window components?
• Why is weather protection important during construction?
• What is the minimum anchor bolt size and spacing?
• SHGC describes what?
• What is commonly required to facilitate inspections?
• Which statement best describes a site plan for permit application?
• What type of insurance coverage should a Home Owner Builder consider?
• What is the minimum drain pipe size?
• How should a Home Owner Builder manage tools and equipment to minimize risk?
• During construction, which insurance coverage should you verify specifically?
• What is the minimum side-to-side clearance for air intake relative to exhaust vents?
• What is a consequence of working without a required permit?
• What does "First occupancy" mean?
• The minimum joist end bearing on framing is best stated as which measurement?
• In a two-plane cladding system, what is the function of the first plane?
• What is the minimum living space ceiling height?
• What temperature must concrete be kept at for 72 hours?
• What is the minimum air space gap behind siding?
• A designer evaluating window performance should consider which set of factors?
• When ownership changes, does the home warranty need to be transferred?
• What is the purpose of a trap seal in plumbing systems?
• What is the minimum interior strip footing width?
• Why might energy calculations be required for Home Owner Builder permits?
• What are typical considerations for homeowner-installed plumbing or on-site septic systems?
• What is the purpose of keeping daily logs and on-site photos during a Home Owner Builder project?
• Which action is part of verifying a subcontractor's license and insurance before starting work?
• If a submittal is rejected, what may be necessary beyond resubmitting?
• In which projects are broader accessibility requirements typically applied?
• Which statement best describes how schedule and permits relate to project milestones and timing?
• What is the minimum slope percentage for flashing?
• Which of the following best describes how on-site inspections support quality control for a Home Owner Builder project?
• What is the purpose of notices to owner or notices of lien rights?
• How do change orders affect the project budget and schedule?
• What is a change order in a construction project?
• In plumbing, why is proper venting important?
• HRV systems help with which of the following?
• Which practice is required when using foam in exterior assemblies to prevent leaks?
• Which of the following is true about site plans in relation to zoning compliance?
• What is a practical approach to ensure quality control on a Home Owner Builder project?
• How should a Home Owner Builder handle an insurance claim related to construction?
• How long must repairs performed under warranty last?
• What is the minimum lap distance on ridge shingles?
• What document is commonly included to waive claims by contractors when a permit closes?
• How should inspections be coordinated with the building department?
• For how long must a residential builder keep track of their activities?
• Which is a required protocol for change orders in a project?
• Under energy performance requirements, you can do what?
• Under what condition can a general contractor be exempt from licensure?
• What is the role of a project schedule in a Home Owner Builder project?
• What is the minimum sill plate size?
• What is the minimum air space behind siding in millimeters?
• Which statement best describes post-construction disclosures requirements?
• What is the minimum door height?
• What is a setback and why does it matter to a Home Owner Builder?
• Which condition must be satisfied before a Certificate of Occupancy is issued?
• What are 'special inspections' and when can they be required?
• Which term is described as the arrangement of openings like windows in a building?
• Which item is included in the 2-year warranty?
• When using subcontractors as a Home Owner Builder, what responsibility does the owner retain?
• In winter, minimizing heat loss via windows is primarily about reducing which characteristic?
• Which factors influence the permitting timeline for a Home Owner Builder project?
• What is required in dwelling units for use during the non-heating season?
• Can a Home Owner Builder occupy a partially completed structure?
• What is the minimum penetration depth for siding nails into framing?
• Under what condition is occupancy generally not authorized?
• The solar heat gain coefficient indicates what?
• Which building codes are generally applied to residential construction under a Home Owner Builder program?
• The 1.2 meter header threshold corresponds to which feet-and-inches measurement?
• The range 210 mm to 235 mm is the minimum size for which element?
• What is the primary purpose of the final inspection in a Home Owner Builder project?
• What is the minimum circular duct overlap?
• A low SHGC would best reduce what?
• What documentation is typically required for final permit closure?